LED assembly units for landscape highlighting
LED assembly units
Designed for general and ornamental interior highlighting, used for street illumination – landscape highlighting, advertisement highlighting of light-boxes, illumination of big-boards etc. 10-13W illuminator with incandescent or halogen lamp is equivalent to 1W LED assembly unit.
LED assembly units are universal; they can be used as without their body so they can also be mounted at different bodies and constructions.
Replacement of almost any illuminator’s filling is possible because of the variety of the assembly units’ configurations.
|
Article: |
1LED 30x30 |
3LED 30x30 |
5 LED 370x20 |
5LED 120x30 |
3LED 252x20 |
6LED 252x20 |
|
|
Power source: |
Direct current 350mA |
||||||
|
Energy input: |
1W |
3W |
5W |
5W |
3W |
3W |
|
|
Number of LEDs: |
1 |
3 |
5 |
5 |
3 |
6 |
|
|
Luminous efficiency: |
Up to 150 lm/W |
Up to 82 lm/W |
|||||
|
LED luminous flux: |
Up to 150lm |
Up to 450lm |
Up to 750lm |
Up to 750lm |
Up to 450lm |
Up to 240lm |
|
|
Angles of radiation: |
80, 170 grades |
170grades |
80,170 grades |
170 grades |
135 grades |
||
|
Emission colour: |
White warm, cold, red, orange, yellow, green, teal, blue, dark blue |
||||||
|
Colour rendering index CRI: |
80Ra |
||||||
|
LED: |
OSRAM (Germany) |
||||||
|
Temperature operative limits: |
from -40°C to +50°C |
||||||
|
Overall size: |
30x30 |
30x30 |
370x20 |
120x30 |
252x20 |
252x20 |
|
|
Service life: |
100000h. |
||||||
|
Warranty: |
18 months |
||||||
|
Allocation: |
Used with the help of thermo-stripe,mounted onto any heat-removing surface |
||||||
Illuminator conforms TU 31.5-31517453-003:2009
Certificate of conformity UkrSEPRO № UA1.035.0076101-09.
Certificate of conformity GOST Р № ROSS UA.AB41.H00102.
With LED illumination you have:
* electricity saving in 5-10 times!
* high light efficiency
* high colour rendering
* high strength and vibration resistance
* absence of starter currents and instant start
* absence of stroboscopic effect
* long-life performance
* low heat emission
* low temperatures resistance
* voltage drops immunity
* environmental safety
LLC Electronic light, at customer’s will produces nonstandard light engineering products using LEDs.
Or…You can make the LED illuminator by YOURSELF
Installation requirements for LED illuminators/assembly units.
Polarity observance:
Not observing the connection polarity the LED breakdown is possible. On the LED from the side of the negative terminal under the lens you can see a spot. For right LED illuminator (assembly unit) connecting there are special plugs that are installed on every illuminator (assembly unit) and on the electric power supply.
Enlarge the connecting scheme Enlarge the connecting scheme2
Observance of the LED quantity in the set:
Not abiding the set amount of LEDs for the specific power supply model the outage of the power supply or/and LEDs breakdown happens. One or more LEDs may be installed in the illuminator (assembly unit). When connecting the illuminators (assembly units) at the specific supply it is necessary to quantify the number of LEDs in the illuminator.
You may install at least 4 and at most 9 LEDs at the power supply JA-32350U.
You may install at least 2 and at most 3 LEDs at the power supply JA-12350U. When installing the illuminator (assembly unit) with one diode, special ballast is installed additionally for this power supply.
You may install at least 10 and at most 24 LEDs at the power supply JA-80350M.
When installing the illuminators (assembly units) with red and yellow LEDs the quantity of the diodes should be multiplied in one and a half time for every power supply.
You mustn’t connect the power supply with no illuminators (assembly units) connected to the electric main of 220V.
Temperature conditions observance:
When overheated the LEDs’ service life is shortened and the breakdown is possible.
The LED assembly unit is to be installed with the use of thermo-stripe onto the heat removing surface.